Litter robot 3 dfi sensor

Hello @Mariagav , Thank you for your reply. According to your order number, the robot is no longer under warranty. If the cleaning of the DFI sensor didn’t fix the issue, we recommend replacing it so you can order a new one from this link: We also recommend replacing the 3 sets of pins so you can order new ones from these links: The following …The DFI repair is actually quite easy to do. You can purchase a replacement DFI from HERE for $30. You can watch this how to VIDEO on how to replace the DFI. The tools needed for this repair are a #2 Philips screwdriver with at least a 6 inch long shank, and needle nose pliers for convenience.The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. ... DFI sensor issue. DFI sensor needs replacing; Replacement Guide (H) YELLOW SOLID: Cycling (In use) Working normally; Without rotation DFI …Litter-Robot 3 Pinch Contact. $5. Buy in monthly payments with Affirm on orders over $50. Learn more. If your Litter-Robot 3 is no longer under warranty, you can purchase this replacement pinch contact.Then, after a minute, go into the Litter Robot driver, refresh, and see if the Cycles After Drawer Full (a counter in the Litter Robot that counts cycles after DFI IR sensor indicates a full drawer) count goes to 0. It’s supposed to go to 0 along with the cycle count when a reset is done.How to Install a Waste Drawer Liner. 1- Remove the old bag. 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app. (For wi-fi model) Note: Steps 4 and 5 must be done in that order according to the manufacturer’s instructions.The issue that you are having would require replacing the DFI sensor and the 3 sets of pins so you can order the following parts from the following links: RobotShop Europe Litter-Robot 3 Open Air DFI Hardware (v2) Litter-Robot 3 Open Air DFI Hardware (v2) Replacement DFI Hardware for your Litter-Robot 3 Compatible with Litter-Robot 3 ...Our litter robot 3 has been barely working for a while. I'd have to hit reset and cycle for it to actually work. Well, about 2 weeks ago it over rotated during a cycle and became "stuck" (wouldn't rotate back into starting position). Putting it back manually caused a yellow flashing light that wouldn't go away.We understand how confusing this could be, but actually the connect version of the Litter-Robot uses a new model of the DFI sensor that only has one not two lenses as the older model. However, the constant blue LED blinking indicates an issue with the DFI sensor so we recommend you to go through this troubleshooting here:I finally gave up on it when it needed the DFI sensor replaced yet again ($80), a common problem on this unit, and bought a PetKit Pura X. This litterbox so far is amazing. It's …Hi, I have a litter robot 3 purchased on the 11-08-2020 - Order No 1036965. We have a continuos flashing yellow light (Pinch Detector Problem) I have completed the following: -. Removed the “2 metal pins” and cleaned them - not dirty and afterwords checked the continuity between them - OK. Checked the 2 magnets - OK. Cleaned the …This manual will help you get the most out of your Liter-Robot. We will guide you through the setup process, as well as provide you with useful tips and advice for acclimating your cat to their new automatic, self-cleaning liter box. Whisker exists to make life for pets and pet parents endlessly beter. As the leading innovators in pet tech and ...To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI. 1 Like. Rutoy21 July 13, 2020, 4:53am 22. @pjutras yes ...Hello, I have a problem with Litter Robot 3. It has blue flashing light at the beginning. I have tried everything (cleaning, reset, check dfi sensor and empty drawer) and when I plug back in it stuck at solid yellow light now (yellow light only). None of buttons is worked even the power button. Any help would be appreciatedIf your Litter-Robot 3 is displaying a yellow light flashing quickly, this indicates a cycle has been interrupted by the Anti-Pinch safety feature and you will need to inspect the pinch sensor. Inspect the sensors. The purpose of the pinch sensor is to detect if an object is blocking the waste port during the globe rotation.Removing the bonnet, flexing/bending back the latches (I discovered I wasn't properly seating the back clasps in-place, this helped a bit with the jerky spinning but failed to avoid the pinch detect fault) Emptied the tray, ensured the bag was installed properly. Emptied the litter entirely and replaced to ensure it's below the fill line.Out little robot has a continuous yellow /amber cycling light and the control panel is totally unresponsive. Things we have tried: Cleaning the pinch sensors Checking the spring sensor Powering off and on (via plug as power button not responsive) Checking for control panel lockout Checked back clips are in Checked globe is locked at the back.Discover solutions for Litter-Robot 3's blue light flashing drawer full issue. Visit our support page now for troubleshooting tips and quick fixes. The store will not work correctly in the case when cookies are disabled. ... Cleaning the DFI Sensors. Let’s take a closer look at the DFI sensors. Debris, such as dust or cat fur, can interfere ...Apr 19, 2021 · r/litterrobot • 3 yr. ago DRob433 LR3 DFI & Pinch Sensor - Preventing Errors? Tips & Tricks Our family has had our LR3 for two years and are mostly in love with it. However, we've had another set of DFI & Pinch Sensors go bad this past week (our 2nd in the last year), which has me concerned about long-term viability of the unit. Purchase replacement pinch contacts and drawer full indicator (DFI) circuit boards here, or if your Litter-Robot is under warranty, log in to your …0:00 / 2:51 Litter-Robot III Open Air - DFI Fault Flashing Blue Light Cat Evolution 516 subscribers Subscribe Subscribed 287 33K views 2 years ago MELBOURNE This video will show you what the...If YES, you are done. Re-position Globe and verify that it completes a clean cycle (in this case adjustment of the cat sensor was not needed). 5. Turn the Base upside down so you are facing the bottom surface. Find the round black adjustment foot and simply turn it Clockwise (2) full complete turns (720 degrees). 6.Litter robot 3 - fast blinking yellow light. Help & Support. Domestic Robots. vanhetpadje December 3, 2023, 1:21pm 1. Hi, What is the meaning of fast (4-5 times a second) blinking yellow light on the liter robot 3? There is a new DFI sensor (the third one!) placed (ordernr 1306269) only 2 months ago. Help appreciated. Thank ...Litter-Robot 3 Pinch Contact. $5. Buy in monthly payments with Affirm on orders over $50. Learn more. If your Litter-Robot 3 is no longer under warranty, you can purchase this replacement pinch contact.Hey, u/PlatformTraining5054! Glad that the new notification is helping you stay ahead of potential issues. Regarding the waste drawer level in the app seeming inaccurate, you could try recalibrating the DFI lasers on your Litter-Robot 4 by following this guide. Hope that helps! r/litterrobot.My litter robot 3 has been working perfectly until 2 weeks ago when it suddenly began getting stuck in the upside down position. ... 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app.Litter-Robot 3 is equipped with infrared emitters and sensors located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light. The unit will cycle again 15 seconds after your cat has left the globe or 5 seconds after the bonnet is replaced. If your Litter-Robot is not detecting your cat or not cycling, complete the troubleshooting steps in our Litter-Robot 3: Cat not detected guide. If your Litter-Robot is slowly flashing yellow or stuck upside down due to the cat ...To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI. 1 Like. Rutoy21 July 13, 2020, 4:53am 22. @pjutras yes it resets it back to solid but every time now after my unit cycles it continues to ...We understand how confusing this could be, but actually the connect version of the Litter-Robot uses a new model of the DFI sensor that only has one not two lenses as the older model. However, the constant blue LED blinking indicates an issue with the DFI sensor so we recommend you to go through this troubleshooting here:I have successfully bypassed the DFI sensor permanently with a under kitchen led tape light section. It has been running for over 1 month 100%. Very easy to do and cost effective that you can do yourself. ... Switched from the Litter Robot bags and am getting 3 more days between emptying.In this case, the DFI sensor and the 3 sets of pins will need to be replaced so we will send you new ones under the warranty. The following videos will show you how to replace these parts: 1- Shipping address. 2- Phone number. 3- Serial number located on the back of the robot.In this case, the DFI sensor and the 3 sets of pins will need to be replaced so we will send you new ones under the warranty. The following videos will show you how …That is a new version of DFI sensor and it fits all Litter Robot 3 versions. It can be installed the same way as the old sensors. It should last much longer since the sensor is smaller and completely protected by protective coating. Feel free to ask anything else. strusland December 29, ...The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. ... DFI sensor issue. DFI sensor needs replacing; Replacement Guide (H) YELLOW SOLID: Cycling (In use) Working normally; Without rotation DFI …LED blue flashing quicker than when the drawer is full and no button of the control panel is working. What should I do? Replace the draw sensors as mentioned in the coments?BEFORE DOING THIS BYPASS HACK:Be sure to do the usual fixes first.. Clean plastic pinch detector part that flexes first (the cracks), then clean both sides o...Litter-Robot Cats Litter Box III 3 Open Air DFI Hardware. by Litter-Robot. Write a review. How customer reviews and ratings work See All Buying Options. 0 total ratings, 0 with reviews ...Hi all, I'm having an issue with my 1 year old litter robot 3 where after every use the app says drawer full and the blue light flashes. I've followed all the litter robot troubleshooting steps including cleaning the lense and re-calibrating the sensor. I've created two support tickets and have been waiting over two weeks for a response from ...We are sorry to hear that you are having trouble with your Litter-Robot. To troubleshoot this issue, please follow the steps below: Thoroughly clean the DFI sensor …The DFI sensor that you have received is the new version and it looks different but it has the exact plastic brackets so you can easily install them the same way as the older sensor: Let us know if you need further assistance. Sincerely, ... Litter-Robot 3 Open Air DFI Hardware (v2) Replacement DFI Hardware for your Litter-Robot 3 Compatible ...Litter Robot owner here -- Have had two litter robots and I think a recent batch of circuits is faulty. First one had no trouble with DFI for years; second one I bought refurbished and DFI went in 2 months. I replaced the DFI on first one, that lasted only 2 months. If Whisker does not get on top of this, they will lose their audience.The Litter-Robot 3 is equipped with infrared emitters and sensors, called DFI sensors, located above the Waste Drawer that check if the drawer is full each time the Globe returns to the Home position. In the event you need to replace your DFI sensors, please follow these instructions. Kit includes: Drawer Full Indicator board assembly (2) retainers1. Turn the base over so it is upside down. 2. Remove the 9 screws connecting the bottom of the base to the top of the base. 1 screw at the back of the unit behind the black cat sensor foot. 3. Gently lift to separate the two halves of the base. The pieces will …If the cleaning of the DFI sensor didn’t fix the issue, we recommend replacing it so you can order a new one from this link: ... Litter-Robot 3 DFI Kit + Pinch Detect Terminals Installation: Litter-Robot 3 DFI Kit + Pinch Detect Terminals Installation - …To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. 1 Like. Litter Robot Connect - dumping clean litter and indicating full tray erroneously. Perpetuus December 22, 2019, 1:03am 3. Thanks for the reply. ...Litter-Robot 3 is equipped with infrared emitters and sensors located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light. Hi, litter robot 3 connect blue flashing light (fast flashing). Have taken the robot apart a few times, cleaned the sensors. ... 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app.DFI Boards to the Base. 3 Figure 10 Figure 12 Figure 9 Figure 11 Figure 13. INSTALL NEW DFI BOARD ASSEMBLY 15. On the front edge of the opening, free the gray ... 1-877-250-7729 or [email protected] LR3-8051-0a. Title: LR3-8051-0a_gr - Installation Guide - DFI.indd Author: mhannaOur litter robot was Flashing Yellow Slow & Fast, then Fast Flashing Blue despite being empty and lastly just Random Lights. Watch for the solution to this, ...LR3 DFI & Pinch Sensor - Preventing Errors? Tips & Tricks. Our family has had our LR3 for two years and are mostly in love with it. However, we've had another set of DFI & Pinch …Hi! I’ve installed a new DFI sensor and circuit-board for the Litter Robot 3 to upgrade to Litter Robot 3 Connect as the DFI sensor on our LR3 had gone faulty and was no longer reporting an accurate level in the waste drawer. On re-assembling the unit, the orange light is flashing slowly, about once per second. I’ve checked that this is not …Since you have not removed them the only 2 possibilities as to why your globe is overshooting the litter leveling portion of the cycle is 1) A bad hall effect sensor or 2) The control board is misinterpreting the motor run time in comparison to the hall effect sensor being triggered by the magnets, what makes this very odd is the fact your ...3. Brush out excess litter. If any litter remains in the robot, brush it away. Wet litter can turn into a clay that is hard to remove. [3] 4. Wash the globe. The globe has no electronic components and thus exposing it to water it is not a concern. Wash with a wet rag and mild soap.Pressing RESET will cancel the DFI flashing, but if the drawer is full, the sensors will action flashing again. The sensors work by sending beams from one sensor to the other, and if the beam is interrupted, the blue light will flash as the Litter-Robot thinks the drawer needs to be emptied.Purchase replacement pinch contacts and drawer full indicator (DFI) circuit boards here, or if your Litter-Robot is under warranty, log in to your …Litter robot 3 yellow light flashing rapidly . I've followed the troubleshooting steps such as: Removing everything from the base, depressing the pinch sensor 10 times, cleaning the terminals and ... and the recommendation was to spend $30 + shipping on a new DFI assembly. The above-linked post fixed the issue in 30 seconds and ...Litter-Robot 3 is equipped with infrared emitters and sensors located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light. Hello, I have a problem with Litter Robot 3. It has blue flashing light at the beginning. I have tried everything (cleaning, reset, check dfi sensor and empty drawer) and when I plug back in it stuck at solid yellow light now (yellow light only). None of buttons is worked even the power button. Any help would be appreciatedThe Litter-Robot 3 is equipped with infrared emitters and sensors, called DFI sensors, located above the Waste Drawer that check if the drawer is full each time the Globe returns to the Home position. In the event you need to replace your DFI sensors, please follow these instructions. Kit includes: Drawer Full Indicator board assembly (2) retainersHello @Mariagav , Thank you for your reply. According to your order number, the robot is no longer under warranty. If the cleaning of the DFI sensor didn’t fix the issue, we recommend replacing it so you can order a new one from this link: We also recommend replacing the 3 sets of pins so you can order new ones from these links: The following …Resolved by: Replacing DFI sensor; Clean contact pins Thread(s): Litter Robot III flashing blue and yellow lights that won't go away; Litter Robot 3 - DFI sensor again and now additional power button issue; Litter robot 3 - blue light flashing followed by rapid flashing yellow light; Litter robot 3.Blue light flashing constantly.Robot stopped ...Litter-Robot 3 is made with standard plastics and the liner is made out of PVC. ... Debris may cause the DFI to indicate a full drawer regardless of the waste in the drawer. ... This will ensure that the automated Cat Sensor is ready for your cat's next visit. Purchase Whisker Cleaner Wipes.If the cleaning of the DFI sensor didn’t fix the issue, we recommend replacing it so you can order a new one from this link: ... Litter-Robot 3 DFI Kit + Pinch Detect Terminals Installation: Litter-Robot 3 DFI Kit + Pinch Detect Terminals Installation - …The issue that you are having would require replacing the DFI sensor and the 3 sets of pins so you can order the following parts from the following links: RobotShop Europe Litter-Robot 3 Open Air DFI Hardware (v2) Litter-Robot 3 Open Air DFI Hardware (v2) Replacement DFI Hardware for your Litter-Robot 3 Compatible with Litter-Robot 3 ...Removing the bonnet, flexing/bending back the latches (I discovered I wasn't properly seating the back clasps in-place, this helped a bit with the jerky spinning but failed to avoid the pinch detect fault) Emptied the tray, ensured the bag was installed properly. Emptied the litter entirely and replaced to ensure it's below the fill line.The DFI sensor that you have received is the new version and it looks different but it has the exact plastic brackets so you can easily install them the same way as the older sensor: Let us know if you need further assistance. Sincerely, ... Litter-Robot 3 Open Air DFI Hardware (v2) Replacement DFI Hardware for your Litter-Robot 3 Compatible ...This topic was transferred to internal RobotShop Support. RobotShop Closed February 11, 2021, 1:00pm 10. Hi! We got a Litter Robot 3 about 6 months ago. Yesterday it showed a Home Position Fault (all lights blinking sequentially from red to blue). I can’t seem to find anything online that deals with this precise issue. ….Resolved by: Replacing DFI sensor; Clean contact pins Thread(s): Litter Robot III flashing blue and yellow lights that won't go away; Litter Robot 3 - DFI sensor again and now additional power button issue; Litter robot 3 - blue light flashing followed by rapid flashing yellow light; Litter robot 3.Blue light flashing constantly.Robot stopped ...Discover how to troubleshoot your Litter-Robot 4's Drawer Full Indicator (DFI) sensors on our support page. Click for step-by-step guidance now. The store will not work correctly in the ... Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels.LR3 DFI sensor needing replacement? Litter-Robot 3 I'm getting the slow blue alternating with rapid yellow when the reset button is pushed. I've permanently bypassed the pinch …Litter-Robot 3: Reset Button. The Reset button will reset your Litter-Robot's Cat Sensor. You can think of the Cat Sensor as the scale and the Reset button as a way to zero the scale. IMPORTANT: Any time you do anything that affects the weight or placement of the unit, including adding or removing litter, emptying the Waste Drawer, or moving or ...LR3 DFI & Pinch Sensor - Preventing Errors? Tips & Tricks. Our family has had our LR3 for two years and are mostly in love with it. However, we've had another set of DFI & Pinch …Description Litter-Robot 3 Open Air DFI Hardware (v2) Replacement DFI Hardware for your Litter-Robot 3 Compatible with Litter-Robot 3 only The Litter-Robot 3 Open Air DFI Hardware (v2) is a replacement DFI Hardware for your Litter-Robot 3. It is compatible with Litter-Robot 3 only.View more What's Included 1x Litter-RoCame home to my Litter-Robot in the upside down position and the yellow flashing (2 flashes per second) and I cannot get the globe to turn at all to try to reset itself. There is power to the unit because the yellow light is flashing but regardless of which buttons I press or turn power on/off no movement of the unit can be made. I have cleaned and …As for the blue blinking light, it’s related to the DFI sensor. Let us know if you need further assistance. Sincerely, Mariagav July 5, 2023, 5:02pm 8. Hi Ebram, Thank you for the information you sent me. I still have a problem: the DFI in my litter robot 3 is longer and different than the one received with my order.Litter Robot Connect version has a new type of DFI sensor based on laser so it has only one circuit board. Old DFI sensor was based on IR light so it had two circuit boards. ... To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light.Discover how to troubleshoot your Litter-Robot 4's Drawer Full Indicator (DFI) sensors on our support page. Click for step-by-step guidance now. The store will not work correctly in the ... Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels.This topic was transferred to internal RobotShop Support. RobotShop Closed February 11, 2021, 1:00pm 10. Hi! We got a Litter Robot 3 about 6 months ago. Yesterday it showed a Home Position Fault (all lights blinking sequentially from red to blue). I can’t seem to find anything online that deals with this precise issue. ….Cleaning your Litter-Robot. It's important to deep clean your Litter-Robot every 3-6 months. Over time, small clumps can accumulate within the internal pocket of the globe, which can contribute to weight-related errors. Cleaning or soaking the globe thoroughly every 3-6 months will help prevent any excess weight from accumulating within the globe.Litter-Robot 3: Litter-Robot 4: Footprint: 24.25″ x 27 ... Additionally, the Robot has integrated a new DFI sensor system, which enables reporting of small changes in the waste drawer’s fullness. In the app, this translates to a percentage-based readout that tells you exactly how full the waste drawer is at any time.If YES, you are done. Re-position Globe and verify that it completes a clean cycle (in this case adjustment of the cat sensor was not needed). 5. Turn the Base upside down so you are facing the bottom surface. Find the round black adjustment foot and simply turn it Clockwise (2) full complete turns (720 degrees). 6.Hello, I have basically the same problem with my litter robot 3 connect. I have tried everything within the trouble shooting like the person said above, I’ve only had it for 1 week. As well I’ve tried to level out the floor for the sensor. But the main problem I am having is the connect only connected to the app successfully for 3 days. And then any …Hi, I have a litter robot 3 purchased on the 11-08-2020 - Order No 1036965. We have a continuos flashing yellow light (Pinch Detector Problem) I have completed the following: -. Removed the “2 metal pins” and cleaned them - not dirty and afterwords checked the continuity between them - OK. Checked the 2 magnets - OK. Cleaned the …Oct 19, 2022 · How to install a replacement DFI Kit + Pinch Detect Terminals in the Litter-Robot 3. The DFI Circuit Board and brackets may appear different from what is pictured depending on when the unit was ... Litter Robot 3 infrared Drawer Full Indicator circuit boards and assembly Kit for a blue flashing light issue. Kit includes DFI board assembly, DFI housing, mounting screws, …My existing DFI sensor looks perfect, and I don't understand why the app wouldn't be able to detect an issue with it independently. The $80 price tag for the component seems absurd and along with the wear on the globe it has me thinking of buying a whole new device. I bought the original Litter robot about 6 years ago and it was life changing.LR3 DFI & Pinch Sensor - Preventing Errors? Tips & Tricks. Our family has had our LR3 for two years and are mostly in love with it. However, we've had another set of DFI & Pinch …1. Turn the base over so it is upside down. 2. Remove the 9 screws connecting the bottom of the base to the top of the base. 1 screw at the back of the unit behind the black cat sensor foot. 3. Gently lift to separate the two halves of the base. The pieces will …Litter-Robot 3: Litter-Robot 4: Footprint: 24.25″ x 27 ... Additionally, the Robot has integrated a new DFI sensor system, which enables reporting of small changes in the waste drawer’s fullness. In the app, this translates to a percentage-based readout that tells you exactly how full the waste drawer is at any time.Hello, I have a problem with Litter Robot 3. It has blue flashing light at the beginning. I have tried everything (cleaning, reset, check dfi sensor and empty drawer) and when I plug back in it stuck at solid yellow light now (yellow light only). None of buttons is worked even the power button. Any help would be appreciatedThe DFI repair is actually quite easy to do. You can purchase a replacement DFI from HERE for $30. You can watch this how to VIDEO on how to replace the DFI. The tools needed for this repair are a #2 Philips screwdriver with at least a 6 inch long shank, and needle nose pliers for convenience.The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If a cycle is interrupted or the bonnet is removed, the unit will stop, and the yellow light will flash slowly, about 1x per second. This will also occur if the cat sensor is activated by a cat entering the globe.To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI. 1 Like. Rutoy21 July 13, 2020, 4:53am 22. @pjutras yes ...Check for obstructions. Check for obstructions that might prevent the cat sensor from functioning. Make sure Litter-Robot is on a firm, level surface. The cat sensor function can be affected if the unit is on carpeting or a litter mat. Check that there are no power cords running underneath the base of the robot that might obstruct movement.Litter Robot 3 - DFI sensor again and now additional power button issue; Litter robot 3 - blue light flashing followed by rapid flashing yellow light; Litter robot 3.Blue light flashing constantly.Robot stopped cycling; Litter-Robot 3 doesn't work (blue blinking light) Litter robot 3 connect has slow blue blinking light or fast yellow blinking ...Note: This problem is EXACTLY the same as this other post I found, which is why I’ve essentially just copied the description from there: Litter Robot Cannot Find Dump Position. Hardware concerned: Litter Robot III Connect. Software concerned: N/A. Troubleshooting steps already taken: unplugging it and plugging it in again; cleaning the …Litter Robot 3 - DFI sensor again and now additional power button issue; Litter robot 3 - blue light flashing followed by rapid flashing yellow light; Litter robot 3.Blue light flashing constantly.Robot stopped cycling; Litter-Robot 3 doesn't work (blue blinking light) Litter robot 3 connect has slow blue blinking light or fast yellow blinking ... | Cwfzehwrk (article) | Mpbqykp.